Gigabit PoE Splitter 12V 1A Output with IEEE 802.3af Standard Compliant 10,100,1000Mbps Power Over Ethernet Splitter Adapter for Security Camera CCTV Surveillance 5.5x2.1mm DC Plug Cable(PS5712G)

Product Information

The Splitter requires a 40V to 56 Volt PoE (power adapter) Gigabit Injector that combines (and injects) the power and the data into a single ethernet cable and sends it to the Splitter. A 48V PoE power injector is typically used and may be installed within 100M of the Splitter. T ype 3, also known as PoE++, can provide up to 60W per PoE port (ensuring a minimum of 51W on each PD port). It's suitable for powering devices such as video conferencing systems components. The 48V to 12V 3A POE+ Gigabit Splitter receives data and power over a single Cat7/Cat6A/Cat6/Cat5e Ethernet cable and splits the power and the data into two output cables (i.e, the 5.5mm x 2.1mm x barrel plug to provide 12 Volt 3 Amps of power to the device, and the RJ45 Ethernet cable to provide the data). This will allow a non-PoE, 5 volt device to be remotely installed and powered over the Ethernet cable (PoE). Keep in mind that when using PoE or power over ethernet switches, or injectors you do not need to use the power adapter connector.

The 48V to 12V 3A POE+ Gigabit Splitter – 5.5mm X 2.1mm Power Plug Tip – Outdoor POE Power LoRaWAN Helium Miner Router WiFi Hotspot Camera Power receives data and power over a single Cat7/Cat6A/Cat6/Cat5e Ethernet cable and splits the power and the data into two output cables (i.e, the 5.5mm x 2.1mm x barrel plug to provide 12 Volt 3 Amps of power to the device, and the RJ45 Ethernet cable to provide the data). This will allow a non-PoE, 12 volt DC powered device to be remotely installed and powered over the Ethernet cable (PoE). Connect the camera to a PoE switch via an ethernet cable, connect the PoE switch to your router, and power on the PoE switch

If you need more cameras or 8 or 16 channel CCTV camera systems, you can think of using a distribution box for better results. PoE) can deliver up to 15.4 watts per port over network cables with 12.95W assured to be available at the powered device. HDMI Specifications and Technical Info | HDMI Voltages, HDMI Wire Layout, HDMI Channels DDC, TMDS and CEC Because they are not dependent on a constant power source, these cameras can be installed in various locations, including areas without electrical outlets. This makes them suitable for both indoor and outdoor use. SHORT CIRCUIT PROTECTION: Any output Short GND Terminal will not damage the Power Supply and will.Auto-Reset.

For most installations we recommend using PoE power where possible, which would consist of either a PoE switch or PoE injector. A 12V DC power adapter is useful for the following situations: We do not offer a weatherproof version of this splitter. However, many of our customers will use this item outside in an enclosed weatherproof box. The operating temperature for this product is -10 to 60 degrees Celcius (40-140 F) However, some devices, like 802.11ac wireless APs with multiple USB ports and radios, need over 30 watts for peak performance. For these cases, PoE++ or PoH switches are the solution. Keep in mind that some devices can adapt to lower power availability by using fewer radios or disabling features. FS Network Switches: Your PoE SolutionBe the first to review “48V to 12V 3A POE+ Gigabit Splitter – 5.5mm X 2.1mm Power Plug Tip” Cancel reply Home Automation Setup / Smart Home Configuration and control from anywhere over WIFI or Voice Commands DSTV XtraView Installation & Frequencies (DSTV User Bands) for Multichoice Explora/HDPVR and other decoders Matt Rossi is a Technical Support Manager at CCTV Camera World, a leading CCTV Camera distributor located in Buffalo, NY. He is a technical support expert for everything video surveillance related. Operating within a voltage range of 44-57V and delivering a current of 10-350mA, IEEE 802.3af provides a maximum power output of 15.4W per port. Due to Ethernet cable power loss, the minimum guaranteed power available at the PD is 12.95W per port. This standard supports devices like VoIP phones and sensors. 2. IEEE 802.3at (PoE+)

The Splitter is equipped with a 5.5mm x 2.1mm barrel power plug which is compatible with most cellular router power connectors, as well as with numerous types of adapters.I very highly doubt the issue is the power supply. Networking requires very little power and even a cheap, off-brand router is capable of sending a signal 100 meters over copper Ethernet. But there's no need to worry, modern network switches are intelligent. When a device is connected, they automatically detect whether it's compatible with PoE or PoE+. If it's a PoE-enabled device requiring 5W, the switch supplies precisely that. If the device demands 20W, the switch steps up. But if you connect a device without PoE capability, rest assured, the switch will deliver data only. How Much PoE Wattages are Need? As mentioned above, IEEE 802.3af delivers a maximum of 15.4W per port, while PoE+ supports up to 30W. The challenge arises when planning to connect multiple devices to a single PoE/PoE+ switch. It's essential to ensure that the total power requirements of these devices do not exceed the switch's maximum power wattage. Single Port Gigabit POE Injector | 12 volt to 52 volt | 1Gb/s for CCTV POE Injector for Cameras / Wifi Access Points / VOIP Phones IEEE 802.3bt is the latest PoE standard that defines two types of powering/wattage standards - Type 3 and Type 4. They will increase the maximum PoE power by delivering more power through two or more pairs of Ethernet cables. In Type 3 and Type 4 modes, PSEs will identify the PDs and allocate power based on the maximum power requirement of the PDs, resulting in an enhanced power delivery system. The standard will include support for 2.5GBASE-T, 5GBASE-T, and 10GBASE-T while existing standards have a maximum speed of 1-Gbps. It's designed for demanding applications such as laptops and LED lighting.